某中型商用车离合器总成设计(含CAD零件图装配图)

某中型商用车离合器总成设计(含CAD零件图装配图)(任务书,开题报告,论文说明书14000字,CAD图7张)
摘 要
离合器普遍存在于以内燃机为动力源的车辆当中,离合器的布置位于发动机和变速箱之间,作用是结合或者切断动力的传递。离合器在其中可以起到顺利使发动机和传动系统结合,并使汽车平稳起动。在换挡时,可以让发动机和传动系统彻底分离,放置动力对传动齿轮造成冲击。
本设计主要述说一款膜片弹簧式离合器,膜片弹簧式离合器在传统离合器上进行了优化设计。并且对离合器中的核心零部件进行了计算校核,使车辆起步更加平稳,同时能对发动机和变速箱起到更好的保护。
关键词:膜片弹簧,离合器,设计
ABSTRACT
Clutches are commonly found in vehicles powered by internal combustion engines. The clutch is arranged between the engine and the gearbox, and its function is to engage or disconnect the transmission of power. In this setup, the clutch can facilitate the smooth connection between the engine and the transmission system, allowing the vehicle to start smoothly. During gear shifting, it can completely separate the engine from the transmission system, preventing power from impacting the transmission gears. [版权所有:http://DOC163.com]
This design mainly describes a diaphragm spring clutch, which is an optimized design of the traditional clutch. Additionally, the core components of the clutch have been calculated and verified, making vehicle start-up smoother while providing better protection for the engine and gearbox.
Keywords: diaphragm spring, clutch, design
3 离合器关键参数的计算
3.1离合器所需参数
本设计是中型商用车离合器的设计,已知数据如下:
整备质量2950kg,额定载质量2990kg,准乘人数3人;发动机额定功率66kW/3200r/min,最大扭矩220Nm/(1900-2200)r/min;变速箱传动比6.80、3.678、2.267、1.421、1.0、倒6.154;最高车速95km/h,后桥速比5.857;其它参数自定。
3.2 摩擦片主要参数的选择
采用单片摩擦离合器是利用摩擦来传递发动机扭矩的,为保证可靠度,离合器静摩擦力矩 需要比发动机最大扭矩 大。
摩擦片的静压力:
=220x1.5=330
式中: 为离合器后备系数。
发动机最大扭矩由上文可得 =220Nm




[资料来源:www.doc163.com]

目 录
第一章 绪论 5
1.1离合器的国内外研究现状 5
1.2离合器作用的概述 5
1.2.1离合器的作用 6
第二章 离合器的结构设计 7
2.1 离合器结构选择与论证 7
2.1.1 摩擦片的选择 7
2.1.2 压紧弹簧布置形式的选择 7
2.1.3 压盘的驱动方式 7
2.1.4 分离杠杆、分离轴承 8
2.1.5 离合器的散热通风 8
2.1.6 从动盘总成 9
2.2 离合器结构设计的要点 10
2.3 离合器主要零件的设计 10
2.3.1 从动盘 10
2.3.2 摩擦片 11
2.3.3 膜片弹簧 11
2.3.4 压盘 11
2.3.5 离合器盖 12
第三章 离合器关键参数的计算 13
3.1离合器所需参数 13
3.2 摩擦片主要参数的选择 13
3.3 摩擦片基本参数的优化 15
3.4 膜片弹簧主要参数的选择 17
3.4.1. 比较H/h的选择 17
3.4.2. R/r选择 17
3.4.3.圆锥底角 18
3.4.4.切槽宽度 18
3.4.5. 压盘加载点半径 和支承环加载点半径 的确定 18
3.4.6. 公差与精度 18
3.5 膜片弹簧的优化 19
3.6膜片弹簧的载荷与变形关系 20
3.7膜片弹簧的应力计算 21
3.8从动盘毂 24
3.9从动轴的计算 25
3.10分离轴承的寿命计算 26 [版权所有:http://DOC163.com]
总结 27
参考文献 28
致谢 29
[资料来源:http://www.doc163.com]
下一篇:某款中型商用载货汽车转向系统的设计(含CAD零件图装配图)
