某款中型商用载货汽车转向系统的设计(含CAD零件图装配图)

某款中型商用载货汽车转向系统的设计(含CAD零件图装配图)(论文说明书14000字,CAD图6张)
摘 要
本次毕业设计的题目是某型载货汽车转向系统的设计,该设计是以转向系统的匹配计算、计算设计转向梯形机构、循环球式转向器设计为主。首先对汽车转向系统的分类及发展情况进行了概述,然后进行了主要车型参数选择,进而确定转向器的形式以及初定其各个参数,进而对转向系统的循环球式转向器的主要部件进行数据校核与受力分析,再后根据前桥的载重情况及人机工程计算转向系传动比。
本次毕业设计选用的是循环球式转向器,该转向器应用于当前大多数汽车上,而循环球式转向器一般的包含了两级传动副,其中第一级传动副是螺杆、钢球、螺母传动副和第二级传动副是齿条、齿扇传动副,第一级传动副是依据相同类型的车辆,从而确定出钢球的中心距离,再计算出其他尺寸,第二级传动副是根据汽车前桥的载重情况计算出齿扇的模数,进而计算出其他一系列尺寸。
本次毕业设计中转向系统的转向梯形机构选用的是应用较多的整体式转向梯形,其中转向梯形机构的设计是选用根据经验公式对梯形机构进行形状和尺寸的确定。
关键词:转向系统,转向器,转向梯形
Abstract [资料来源:https://www.doc163.com]
The topic of this graduation project is the design of the steering system of a certain type of cargo truck. This design focuses mainly on the matching calculation of the steering system, the calculation and design of the steering trapezoidal mechanism, and the design of the recirculating ball type steering gear. First, an overview of the classification and development of automotive steering systems is provided, followed by the selection of the main vehicle parameters. Then, the form of the steering gear is determined and its various parameters are initially set. Afterwards, data verification and stress analysis are carried out on the main components of the recirculating ball type steering gear of the steering system. Finally, the steering system transmission ratio is calculated based on the load on the front axle and ergonomic considerations.
In this graduation project, a recirculating ball type steering gear is chosen, which is used in most current automobiles. The recirculating ball type steering gear generally includes two stages of transmission pairs: the first stage is composed of the screw, steel ball, and nut transmission pair, and the second stage is composed of the rack and sector transmission pair. The first stage transmission pair is determined based on vehicles of the same type, thereby establishing the center distance of the steel balls, then calculating other dimensions. The second stage transmission pair is calculated according to the load on the front axle of the vehicle to determine the module of the sector, followed by a calculation of a series of other dimensions.
In this graduation project, the steering trapezoidal mechanism of the steering system uses the commonly applied integrated steering trapezoid. The design of the steering trapezoidal mechanism is based on empirical formulas to determine its shape and dimensions.
Key words: steering system, steering gear, steering trapezium
2 参数选择
本文采用某款中型商用车的整车参数作为计算标准,具体参数如下:
2.1 整车信息
驱动型式4×2;外形尺寸(mm)5995×2090×2260;货箱4150x1990x450mm;前/后轮距1586/1530mm;轴距3300mm;前/后悬1115/1265mm;整车6135kg,整备质量2950kg,额定载质量2990kg,准乘人数3人;接近离去角20/15;发动机额定功率66kW/3200r/min,最大扭矩220Nm/(1900-2200)r/min;变速箱传动比6.80、3.678、2.267、1.421、1.0、倒6.154;前轴荷2700kg,弹簧片数8/9+5;最高车速95km/h,后桥速比5.857;最大转向角40°;轮胎规格6.50R16/7.00R16,数量6个,液压制动;其它参数自定。
[资料来源:www.doc163.com]





[资料来源:www.doc163.com]
目 录
摘 要 I
Abstract II
1 绪论 1
1.1 纯机械式转向系统 1
1.2 液压助力转向系统 1
1.3 电动助力转向系统 2
1.4 线控转向系统 2
2 参数选择 4
2.1 整车信息 4
3 转向系统设计概述 5
3.1 对转向系统的设计要求 5
3.2 转向操纵机构 5
3.3 转向传动机构 6
3.4 转向器 7
3.5 转角及最小转弯半径 7
4 汽车转向系方案的选择 9
4.1 转向系的主要性能参数 9
4.1.1 转向器的效率 9
4.1.2 传动比变化特性 10
4.1.3 转向器传动副的啮合间隙 12
4.1.4 转向盘的总转动圈数 12
5 转向系的设计计算 14
[资料来源:Doc163.com]
5.1 转向器的设计计算 14
5.1.1 螺杆、钢球、螺母传动副的设计 14
5.1.2 齿条、齿扇传动副的设计 16
5.2 循环球式转向器的强度计算 21
5.3 转向摇臂轴直径的确定 23
参考文献 25
致 谢 26
[资料来源:Doc163.com]
下一篇:轻型两驱皮卡货车变速器(手动变速箱)设计(含CAD零件图装配图)
