Open Nav

注塑模的参数控制型腔布局设计系统

以下是资料介绍,如需要完整的请充值下载.
1.无需注册登录,支付后按照提示操作即可获取该资料.
2.资料以网页介绍的为准,下载后不会有水印.仅供学习参考之用.
   帮助中心
资料介绍:

注塑模的参数控制型腔布局设计系统(中文6100字,英文4000字,英文PDF)
M. L. H. Low and K. S. Lee
机械工程系,新加坡大学,新加坡
摘要
如今,塑料产品的上市时间变的越来越短,因此,制造注塑模的可用交货时间也变的少了。在模具的设计阶段有个省时的潜在方法,因为由于每个模具设计可以是标准化的,所以一个设计程序可以被重复使用。本文提出了一种通过使用标准模版来控制几何参数的方法来设计注塑模的型腔布局。标准模版的型腔布局设计包括可能布局的配置。每个布局设计的配置都有其特有的由所有几何参数构成的布局设计表格。这个标准模版是预定义在合型设计的布局设计的级别时的。这样就能够确保要求的配置能够被快速地输入到模具装配设计中,而不需要重新设计布局。这使得它在模具制造前产品设计师和模具设计师之间的技术讨论上更有用。在讨论时直接改变3D型腔的布局设计,这样可以节省时间和避免错误传达。型腔设计的标准模版便于各个模具制造公司依照顾客具体要求而制造他们各自的规格。
关键词:型腔布局设计;几何参数;合型;注塑模设计;标准模板

一、    外文原文
A Parametric-Controlled Cavity Layout Design System for a Plastic Injection Mould

[来源:http://www.doc163.com]


M. L. H. Low and K. S. Lee
Department of Mechanical Engineering, National University of Singapore, Singapore
Today, the time-to-market for plastic products is becoming shorter, thus the lead time available for making the injection mould is decreasing. There is potential for timesaving in the mould design stage because a design process that is repeatable for every mould design can be standardised. This paper presents a methodology for designing the cavity layout for plastic injection moulds by controlling the geometrical parameters using a standardisation template. The standardization template for the cavity layout design consists of the configurations for the possible layouts. Each configuration of the layout design has its own layout design table of all the geometrical parameters. This standardisation template is pre-defined at the layout design level of the mould assembly design. This ensures that the required configuration can be loaded into the mould assembly design very quickly, without the need to redesign the layout. This makes it useful in technical discussions between the product designers and mould designers prior to the manufacture of the mould. Changes can be made to the 3D cavity layout design immediately during the discussions, thus saving time and avoiding miscommunication. This standardisation template for the cavity layout design can be customised easily for each mould making company to their own standards.
[资料来源:http://Doc163.com]

Keywords: Cavity layout design; Geometrical parameters;
Mould assembly; Plastic injection mould design; Standardisation
 
[资料来源:Doc163.com]

注塑模的参数控制型腔布局设计系统

  [资料来源:http://doc163.com]

  • 关于资料
    提供的资料属本站所有,真实可靠,确保下载的内容与网页资料介绍一致.
  • 如何下载
    提供下载链接或发送至您的邮箱,资料可重复发送,若未收到请联系客服.
  • 疑难帮助
    下载后提供一定的帮助,收到资料后若有疑难问题,可联系客服提供帮助.
  • 关于服务
    确保下载的资料和介绍一致,如核实与资料介绍不符,可申请售后.
  • 资料仅供参考和学习交流之用,请勿做其他非法用途,转载必究,如有侵犯您的权利或有损您的利益,请联系本站,经查实我们会立即进行修正! 版权所有,严禁转载
    doc163.com Copyright © 2012-2024 苏ICP备2021029856号-4